Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Bathtub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Bathtub Surround
Blog Article
They are making a few good annotation about Installing A Bathtub as a whole in the article followed below.
Installing a tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, and often, tiling abilities. Replacing an old bathtub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move rapidly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old bathtub and set in the brand-new one. See to it you have qualified yourself for the task as well as fit attempting it. Rather than employing a service provider to take over a halfway-completed project, it is much better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube connections.
This short article will assist you mount a brand-new bath tub in your washroom if you have actually currently acquired a brand-new bathtub and also do not require to alter the plan of your previous water system pipelines.
Your tools as well as material checklist ought to comprise the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The procedure of removing the existing faucets can be fairly troublesome due to the limited gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline links on the old taps to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the producer offered backnut. When the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap finishes initially, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bath tub in the called for setting. The wooden boards are useful in evenly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub until the level reads level.
To mount faucets, fit all-time low of the furthest versatile faucet port to the suitable supply pipe by making a compression join; after that do the very same for the various other tap.
Switch on the water supply and examine all joints and also new pipework for leaks and tighten them if essential. Load the tub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bathtub needs to wait till the tub has been made use of a minimum of when as this will certainly settle it right into its final position.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom ought to be fitted (if required) according to the maker's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps system to prevent pressure on the bathtub.
Fit the adaptable tap ports to the bottom of the two faucets using 2 nuts as well as olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last position.
Tiling Around the Tub
In the location where the bath satisfies the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to fracture a rigid seal, triggering the water to permeate the wall surface between the bath as well as the tiling, bring about complications with dampness as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, and also can securing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of soaked newspaper or soft rope. Remember to always fill up the tub with water prior to securing, to permit the activity experienced when the tub is in use. The sealant can break relatively early if you do not take into consideration this movement before sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are likewise quickly offered on the marketplace. It is a good idea to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was shown that write-up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through someone on a different web blog. Are you aware of somebody else who is excited about the topic? Do not hesitate to share it. I cherish reading our article about How to Install a Bathtub Yourself.
Schedule A Free Estimate
Report this page